E3 Replacement Terminal Blocks
# of Pins | PT # |
Description |
4 | KPTV0041 |
RS485 terminal |
6 | KPTV0061 |
Power Input Terminal |
17 | KPTV0171 |
I/O Terminal for E3-MIX24880, E3-MIX24882, E3-32DI24, E3-32DO24, E3-32AI20M, E3-32AI10V, E3-16DI24, E3-16DIAC, E3-16DO24, E3-8AO20M, E3-16AI20M, E3-16AI8AO, E3-16ISOTC, 16ISO20M, E3-10RTD |
18 | KPTV0181 |
E3-MIX20884 |
SixTRAK Spare Parts
Products:
ST-IPm-8460/VT-IPm-1410/ET-GT-ST-3
Replacement Part Number |
Description |
KHXSTIOS |
Din Clip Spring |
KMSIX000 |
Plastic Din Clip |
Instructions to add din clip:
- Enter spring spring into Din Clip
- Slide clip into plastic.
VersaTRAK Spare Parts
Products:
VT-mIPm-245-D/VT-mIPm-135-D/VT-IPm2m-213-D/VT-IPm2m-113-D/VT-uIPm-431-H
Replacement Part Number |
Description |
VT-IPM2M-113-DB |
Replacement BASE for VT-IPM2M-113 |
VT-IPM2M-113-M |
Module ONLY VT-IPM2M-113 |
VT-IPM2M-213-DB |
Replacement BASE for VT-IPM2M-213 |
VT-IPM2M-213-M |
Module ONLY VT-IPm2m-213 |
VT-MIPM-135-DB |
Replacement BASE for VT-MIPM-131 |
VT-MIPM-135-M |
Module ONLY VT-MIPM-131 with IPM-CPU-5 |
VT-MIPM-245-DB |
Replacement BASE for VT-mIPm-245-D |
VT-MIPM-245-M |
Module ONLY VT-MIPM-245 with IPM-CPU-5 |
VT-UIPM-431-HB |
Replacement BASE for VT-UIPM-431 |
VT-UIPM-431-M |
Module ONLY VT-UIPM-431 with IPM-CPU-1 |
KHXSTIOS |
Din Clip spring |
KMSTCLP2 |
Din rail plastic clip |
How to replace a VersaTRAK IPm Module or Base
Replacement Module
-
- VersaTRAK IPm bases contain the IP address and serial number configuration but not the program, I/O Transfers, etc.
- Replace the module by removing power. Then remove the module from the baes. Plug in the replacement module.
- Load the configuration and program from the Sixnet I/O Tool Kit configuration software via Ethernet or serial.
Replacement Base
-
- The base component holds the communication serial number and communication parameters. When replacing the base update the Sixnet I/O Tool Kit configuration with the new serial number and reload via serial.
- Remove power. Unwire the old base and re-wire the replacement base.
- Load basic configuration via Port B using the included RJ45-DB9F-IPm and a straight-thru Ethernet cable.
EtherTRAK-2 Spare Parts
Products
E2-MIX24880-D/E2-MIX24882-D/E2-MIX20884-D/E2-8AO20M-D/E2-32AI20M-D/E2-32AI10V-D/E2-32DI24-D/E2-32DO24-D/E2-16AI20M-D/E2-16AI-8AO-D/E2-16DI24-D/E2-16DIAC-D/E2-16DO24-D/E2-16DORLY-D/E2-16ISO20M-D/E2-16ISOTC-D/E2-10RTD-D
Replacement Part Number |
Description |
E2-10RTD-M |
Module only |
E2-16DORLY-M |
Module only |
E2-16ISO20M-M |
Module only |
E2-16ISOTC-M |
Module only |
E2-8AO20M-M |
Module only |
E2-32DI24-M |
Module only |
E2-BASE-1 |
Replacement base for all E2 module except E2-MIX20884-D/E2-16ISO20M-D/E2-16ISOTC-D. |
E2-BASE-TC-1 |
Replacement base for E2-16ISOTC-D |
E2-BASE-20M-1 |
Replacement base for E2-16ISO20M-D |
E2-HLDDN-2 |
Set of clips (2 per module) help keep the module steady in high vibration environments. Not required for high vibration environments. |
RJ45-DB9F-CBL |
One pre-wired RJ45-DB9F-IPm and two (one male one female DB9) unwired for user-configured pin-out. |
KME2CLP1 |
Red, short base clip. To secure the base to the din-rail when the I/O Module is mounted parallel to the din-rail. |
KME2CLP2 |
Red, long base clip. To secure base to the din-rail when the I/O Module is mounted perpendicular to the din-rail. |
KME2CLP0 |
Red Module clip to secure module to base. Two per module. |
KME2KEY0 |
Module key; two per module. |
KME2KEY1 |
Base key; two per base. |
How to replace a EtherTRAK-2 Module or Base
Replacement Module
-
-
- The EtherTRAK-2 base stores all the configuration parameters. To replace a module power down the unit, unplug existing module and plug-in new module.
- Once powered up the module will be operational again.
-
Replacement Base
-
-
- Power down the I/O Module and base. Unwire the base and rewire the new one.
- Plug the old module into the replacement base. Load the configuration from the Sixnet I/O Tool Kit via Ethernet.
-